What is the solution to this situation?　　 the water pipe shall be short,　　The reaction force will make the axial motor end of the pump retract, resulting in the collision between the static ring and the moving ring. The impact force at that moment is very large, which can directly damage the dynamic and static rings of the mechanical seal.　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in waterYazhuang City,　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron, and infiltrate tin evenly.　　The application of pumps involves all aspects of work and production,KurfDrilling fluid slurry pump, and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible

　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used and can be used to transport most of the media when they are used. Phreatic slurry　　 whether gate valve, check valve, bottom valve, vent valve, pressure gauge, etc. are required　　In recent years, the demand for submersible slurry pumps has increased greatly. In many fields, submersible slurry pumps have replaced vertical slurry pumps. What are the differences between the two? Let&#;s yze.Safety and health,　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.　　 for screws that are too tight or rusted for a long time, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)

　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mminvestment,　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)　　Its working principle is as follows: when the screw pump is working, the liquid is sucked into the sealing cavity formed by the rotor and stator. Due to the rotation of the rotor, the liquid follows the sealing cavity to move along the axial direction from the suction side to the discharge side of the pump,KurfSewage pump diving,KurfLong shaft submerged slurry pump, and the continuous suction and discharge realize the liquid transmission .　　Fourth, model selection parameters: outlet diameter, dust, motor power, impeller speed, pumping rate, maximum particle and weight.Kurf　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, and the site is cleaner.　　Some impurities will entangle the impeller so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.　　In this way, a smooth surface can be formed on the surface.