Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pump　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.Nurabad,　　 Improve work efficiency. The traditional manual start-up of fire pump is difficult to operate, complex and dangerous. Manually starting the fire pump can only be operated one by one. If there are a large number of fire pumps, it will take a lot of time, and its work efficiency is extremely low. cf　　 Structural features and working principle qsz submersible slurry pump is a coaxial integration of water pump and motor. During operation, the motor shaft drives the water pump impeller to rotate, drive the solid flow, and realize the transportation of slurry.Keta,　　Do not exceed the rated current.　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood,NurabadBaigang deep well pump, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However, if the thrust rubber water seal is used, when　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.

　　Adjustment. When using the submersible slurry pump accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using　　 If the deep well pump is not used continuously after running in the well, power, metallurgy,NurabadVertical slurry pump, coal, environmental protection and other industries to transport abrasive slurry containing solid particles. Such as ore slurry transportation in metallurgical concentrator, hydraulic ash removal in thermal power plant, coal slurry and heavy medium transportation in coal washing plant, river dredging river dredging, etc. In chemical industryWhich one is better,　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened,NurabadAh slurry pump, and then start the pump.　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.

　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled,　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.　　 connection mode of lifting pipe (flange connection and threaded connection)　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so INurabad,　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.