A non scissor type hydraulic lifting mechanical equipment used for transporting goods between floors of industrial factories, restaurants, and restaurants on the second and third floors. Professional elevator manufacturers are safe, environmentally friendly, and economical! Our products are exported to foreign countries and highly trustedBrunswick,Outbound call form: Outbound call boxes are pre embedded or installed in a column style on the wall or ground near the parking floor above and below the platform, and are linked to operate the platform up and down.Ensure that the small gear and pressure wheel are securely fastened on the drive base plate, and check the fixing condition of the drive base plate boltsBab EzzouarCheck the clearance of the ball bearing and the wear of the suspension wheel guide wheel. If the roller is worn, it is necessary to adjust or replace it. If the elevator bearing is worn,BrunswickAluminum alloy hydraulic lifting platform, replace the guide wheel or bearingAfter cleaning clean the filter and replace it with a new filter element before adding new oil. What adverse reactions may occur during the early use of hydraulic cargo elevators?Leakage occurs due to looseness, vibration, and the influence of heat on the sealing surface and pipe joints of the machine; Some casting, processing and other defects are difficult to detect during assembly and debugging but due to vibration and impact during the operation process, these defects are exposed, leakage is prone to occur during the running-in period. Poor, due to the small fit clearance of newly assembled components and the difficulty in ensuring the uniformity of fit clearance due to assembly and other reasons, oil (grease) is not easy to form a uniform oil film on the friction surface to prevent wear. This reduces efficiency and causes early abnormal wear of the components. In severe cases, it can cause scratches or bite on the friction surface of precision fitting, leading to the occurrence of faults.

The surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %.Power supply voltage: Motor power: Lifting: Rocker self reset switch operation Overload protection: Over current relay.Ensure that power cables and electrical circuits are not damagedmarket price,Check the interlocking equipment, up and down travel, and other safety maintenance switches of the cage door and fence doorOn the contrary, it should be adjusted in the opposite direction; When the meshing backlash of the gear pair is greater than .mm, loosen the connecting nut of the eccentric shaft of the guide roller and the tooth back pressure wheel as shown in , adjust the tooth back pressure wheel to press towards the back plane of the gear rack until the backlash reaches a reasonable range. Otherwise, the guide roller should be loosened for o and then adjusted according to the adjustment of the guide roller.There are many operational errors, and due to insufficient understanding of the structure and performance of the machine (especially for new operators), it is easy to cause malfunctions and even mechanical accidents due to operational errors. How to calculate the lifting cargo elevator? A lifting cargo elevator is a heavy lifting mechanical equipment that can manually operate the system's buttons to complete the transportation of goods up and down. The lifting height of the lifting cargo elevator varies from meter to meters, and special specifications of lifting and lowering cargo elevators can be customized according to user requirements According to the type, it can be divided into:; Scissor fork type cargo elevator and guide rail type cargo elevator. Guide rail type elevator is a non scissor fork type cargo elevator, mainly used for the transportation of goods between floors of workshops, hotels,BrunswickScissor fork mobile lifting platform,BrunswickOutdoor guide rail type lifting platform, rooms, and warehouses without pits or machine rooms. Scissor fork type cargo elevators need to be prepared with pits before installation, and the elevator should be fixed and connected in the pit before being connected to the power supply The lifting cargo elevator utilizes hydraulic power units to generate pressure during operation, which drives the hydraulic oil cylinder as the main power to raise and lower the lifting cargo elevator platform. When a guide rail type hydraulic lifting cargo elevator malfunctions, it can immediately stop running, with high safety and stability. The driving of the hydraulic power unit makes it have strong load-bearing capacity and smooth lifting, which can achieve the transportation of large tonnage goods

Ensure that power cables and electrical circuits are not damageddevice management,Regularly check the connection of each part and tighten it if there is any looseness. The tightness of the body connecting bolts should be checked when the body is under pressure (the rotating arm can be used to cause compression)Emergency stop: Press the emergency button switch to raise or lower the machine.How to maintain and maintain the stage? When using the lifting stage in daily life, attention should be paid to maintenance to extend its lifespan. Below, there should be no dirt present, and any dirt must be washed off with gasoline or thinner. Pay attention to checking each steel wire rope for broken wires and loose strands. If it exceeds the relevant regulations, it must be replaced immediately. Professional elevator manufacturers have a complete range of products which are popular both domestically and internationally. Our equipment has a long service life! The industry leader in product wire products, welcome to inquireBrunswick,After cleaning, clean the filter and replace it with a new filter element before adding new oil. What adverse reactions may occur during the early use of hydraulic cargo elevators?The lifting stage is a high-altitude operation equipment, and prolonged use can cause loose connections between some components. So in order to ensure the personal safety of construction workers, it is necessary to regularly inspect the lifting stage and tighten any loose components. The lifting stage is a high-altitude operation equipment, and prolonged use can cause loose connections between some components. So in order to ensure the personal safety of construction workers, it is necessary to regularly inspect the lifting stage and tighten any loose components. The interference and hazard analysis of the frequency conversion speed regulation construction elevator circuit is becoming increasingly widespread in the development of technology today. Variable frequency speed regulation has the characteristics of stable start and stop process, reducing mechanical shock, increasing the comfort of passengers, and improving the service life. At the same time, it can also change the speed of power supply frequency regulation, save electric energy, and improve work efficiency. However, there will be interference in the use of variable frequency speed regulation system, which will often cause safety accidents of construction elevator.Quarterly maintenance: Check the items checked each month