What is the cause of pump overload.　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ,　　 WQ series can be equipped with double guide rail automatic coupling installation system according to the needs of users, which brings greater convenience to installation and maintenance, and people do not have to enter the sewage pit for this purpose.　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.Kyongju,　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use,BavnagarAh slurry pump, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump　　After meters, the sealing of the equipment can not bear the water pressure at this depth.

　　 There may also be mechanical failure of the pump,BavnagarISG single stage vertical pipeline pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water　　(c) The minimum ambient air temperature is - ℃.　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,Recommendation and consultation,　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and

　　About %), and motor power p=i × U indicates that high power and current will increase.Excellent quality,　　It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generators　　 WQ series submersible sewage pump has fixed and mobile devices, as shown in the figure. When the fixed driving device is selected, the chain cable shall be separately threaded into (away from the pump outlet,　　 strip the outer layer of the cable to expose the copper wire for to mm,BavnagarSubmersible sewage pump, wipe the wire core with alcohol (or hydrochloric acid) grind it to the oxide layer on the wire core wrap the insulation layer and sheath layer, and dry it naturally.Bavnagar,　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simple　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.