Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry.Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, the heating temperature shall not exceed ℃, so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.Yamasa,After the pipeline is installed and the pressure test is qualified, it is better to wash with low chloride ion water and disinfect with .% potassium permanganate.. It is our responsibility not to pay attention to the maintenance of the pipe during transportation, mix the pipe with corroded chemical commodities, which will cause rust. . It is the responsibility of the processor and manufacturer. When cutting stainless steel or iron when manufacturing goods, it is only reasonable for highly skilled technicians to deepen investigation and discussion, make a reasonable division of responsibilities, and who should be responsible for whose achievements. You can't let steel mills, pipe factories, processors, or users bear the liability for compensation!Leribe,After molten steel casting, stainless steel pipe fittings generally adopt the same vertical, vertical bending or arc continuous caster as carbon steel. The refined molten steel is poured into the ladle, the ladle to be poured is transferred above the tundish mouth through the rotary table, and then the molten steel is tundish through the long nozzle. The molten steel in tundish enters the mold through the submerged nozzle for forming, condensation and continuous downward movement.Austenitic stainless steel can be used to manufacture stainless spring, clock spring and steel wire rope in aviation structure after deformation strengthening. If welding is required after deformation, spot welding process and deformation can only be used to increase the tendency of stress corrosionWhen improved, it is possible to use it in refrigeration related engineering. Recently, suslx (cr Ti, Nb LC) and susl have been applied to frozen shells. Ferritic stainless steel has body centered cubic structure. When the material properties become weaker, sharp cracks will expand rapidly and cause brittleness. Austenitic series stainless steel will not produce brittleness because it has face centered cubic structure. Austrian stainless steel SUSL (cr-ni LC) and SUSL (cr-ni-mo-lc) shows that it still has superior impact characteristics at low temperature. However, pay attention to the precipitation of ferrite or martensite due to processing, and the tendency of embrittlement due to sensitized carbide or & sigma; equal heterogeneous precipitation.

The back side is not protected by argon, and the flux coated welding wire (self protective flux cored welding wire) + TIG process is adopted. In the s, the backing welding wire has been developed. Recently, China has also developed the stainless steel backing welding wire (i.e. flux coated welding wire such as tgftgftgftgf, the second widely used steel is mainly used in food industry and surgical equipment. Molybdenum is added to obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than it etc.) It has been applied to the actual construction and achieved good results. We have successfully applied it in the capacity expansion and reconstruction project of Urumqi Petrochemical.　　— After that,YamasaStainless steel pipe 201, it is also made & ldquo; Marine Steel & rdquo; To use. SS is usually used in nuclear fuel recovery units. Grade stainless steel generally meets this application grade. [] Model & mdash; Except that the risk of weld corrosion of the material is reduced due to the addition of titanium, other properties are similar.Production process of stainless steel pipe A. preparation of round steel; b. Heating; c. Hot rolling perforation; d. Cutting head; e. Pickling; f. Grinding; g．； h. Cold rolling; i. Degreasing; j. Solution heat treatment; k. Straightening; l. Pipe cutting; m. Pickling; n. Finished product inspection.offer,Ferritic and martensitic stainless steels are represented by series numbers. Ferritic stainless steel is marked with and , martensitic stainless steel is marked with and C, dual phase (austenite ferrite).Crimping: during crimping, the convex part of the pipe fitting is placed in the concave groove of the die, and the jaw is perpendicular to the pipe axis.Solution treatment. The main purpose of water quenching after heating the steel to ~ ℃ is to dissolve the carbide in austenite and keep this state to room temperature, so that the corrosion resistance of the steel will be greatly improved. As mentioned above, in order to prevent intergranular corrosion,YamasaStainless steel high pressure pipe, solid solution treatment is usually used to dissolve CrC in austenite and then cool rapidly. Air cooling can be adopted for parts, and water cooling is generally adopted.

At low temperature ferritic stainless steel pipe has low-temperature brittleness like carbon steel, ferritic or martensitic stainless steel produces low-temperature brittleness, it is necessary to pay special attention when using at low temperature. As a way to improve the impact toughness of ferritic series stainless steel, the embrittlement temperature is in the range of - ℃ to - ℃Home page recommendation,Decorative stainless steel pipe: usually the outer wall is relatively bright, so its name is considered. Decorative stainless steel pipe is used for decorative purposes. The stainless steel pipe for general decorative purposes is relatively thin. Because it is different from the manufacturing process of stainless steel product pipe, the price also varies greatly. The general production process of decorative stainless steel pipe is ordinary welded stainless steel pipe. Guangdong stainless steel product pipe stainless steel product pipe: generally, the surface of stainless steel product pipe is also a bright surface, and a small number of pipes with acid pickling industrial surface. As mentioned above, stainless steel product pipe belongs to the purpose of stainless steel products, because the outer diameter size, mechanical properties, acid, alkali and corrosion resistance of stainless steel pipe are relatively good, Therefore, stainless steel pipes are generally used as anti-corrosion materials or hardware products in large-scale production enterprises. The production process of stainless steel pipes is one-time forming, and nitrogen protection is also added during welding.In polluted air (such as atmosphere containing a large amount of sulfide carbon oxide and nitrogen oxide), in case of condensed water, acetic acid liquid points will be formed, which will lead to chemical corrosion.. Domestic wce cerium tungsten electrode is used for electrode data. The shape and diameter of the end of cerium tungsten electrode have a great impact on the fluctuation of welding process and weld formation.Yamasa,When improved, it is possible to use it in refrigeration related engineering. Recently, suslx (cr Ti, Nb LC) and susl have been applied to frozen shells. Ferritic stainless steel has body centered cubic structure. When the material properties become weaker, sharp cracks will expand rapidly and cause brittleness. Austenitic series stainless steel will not produce brittleness because it has face centered cubic structure. Austrian stainless steel SUSL (cr-ni LC) and SUSL (cr-ni-mo-lc) shows that it still has superior impact characteristics at low temperature. However, pay attention to the precipitation of ferrite or martensite due to processing, and the tendency of embrittlement due to sensitized carbide or & sigma; equal heterogeneous precipitation.Austenitic stainless steel has good resistance to uniform corrosion,YamasaStainless steel natural gas pipe, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, the greater the tendency of intergranular corrosion. In addition, intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich CrC on the grain boundary. The chromium poor area is formed in the surrounding matrix which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.Stress relief treatment. Stress relief treatment is a heat treatment process to eliminate the residual stress of steel after cold working or welding. It is generally heated to ~ ℃ for tempering. For steels without stabilizing elements Ti and Nb, the heating temperature shall not exceed ℃, so as to avoid intergranular corrosion caused by chromium carbide precipitation. For cold worked and welded parts of ultra-low carbon and stainless steel containing Ti and Nb, they need to be heated at ~ ℃ and then cooled slowly to eliminate stress (the upper limit temperature is taken for eliminating welding stress), which can reduce the tendency of intergranular corrosion and improve the stress corrosion resistance of steel.