The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform,The daily maintenance of guide rail lifting equipment should pay attention to regular inspection and maintenance eliminate hidden dangers, and eliminate faults. Doing this is good for improving work efficiency,Wu'anGuide rail chain lifting cargo elevator, prolonging the service life of equipment and ensuring the safety performance of the elevator.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases,Wu'anProduction of lifting cargo elevators, the winding will be burned.Banora Point,Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods,Wu'anFive ton cargo elevator, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.

What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.Manual hydraulic lifting platform application manual hydraulic platform performance: manual hydraulic platform vehicle is made of high-strength steel, the design structure is reasonable and compact, safe, stable and reliable, built-in safety valve fully sealed oil cylinder, manual hydraulic system lifting, easy to operate. Equipped with guide wheels to save the operator's physical strength, and can protect the load wheels and pallet load wheels. Unique hydraulic pump design, the pump is simple and designed to maintain an ideal height for assembly line loading and unloading operations; coupled with the unique design concept, the operator's operation is simple and convenient.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.offer,Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.

Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.Trustworthy,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.It is strictly forbidden for two persons working at heights to use the same safety rope at the same time.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Wu'an,This kind of fixed lifting equipment can also be used in the warehouse. For example, scratches, small rocks on the driving tires there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface and if there is dirt, it must be washed off with gasoline or thinner.