Adjust the ratio of austenite forming elements to ferrite forming elements in the steel to make it have austenite + ferrite dual phase structure, in which ferrite accounts for % - %. This dual phase structure is not easy to produce intergranular corrosion.When water-soluble paper is used to block the ventilation, due to the ventilation from the weld center, the ventilation pipe shall be pulled out quickly at the later sealing link, and the residual argon inside shall be used for protection, so as to quickly finish the bottom and seal the mouth.Port Abbas,The requirements for weldability and weldability vary from product to product. A tableware usually does not need welding performance, and even includes some pot enterprises. However, most products require good welding performance of raw materials such as class II tableware, thermos cup, steel pipe, water heater, water dispenser,Bidirectional Product Description: the tensile strength of the material is ~ mpa, and the high working temperature can reach ℃.After molten steel casting, stainless steel pipe fittings generally adopt the same vertical, vertical bending or arc continuous caster as carbon steel. The refined molten steel is poured into the ladle, the ladle to be poured is transferred above the tundish mouth through the rotary table, and then the molten steel is tundish through the long nozzle. The molten steel in tundish enters the mold through the submerged nozzle for forming, condensation and continuous downward movement.Flux coated welding wire is used for backing welding, and argon gas is not used inside the weld. The welder's operation is simple and fast

Application field: tubular boiler for pipeline in harsh seabed environment product description: ultra (ultra) critical unit is the basis of modernization of power generation equipment and energy conservation and emission reduction. Among the important pressure parts of ultra (supercritical) boiler, superheater and reheater are the parts with high working temperature and bad working environment. Previously, all such materials used in China were imported from abroad,Port Abbas630 stainless steel strip, while only steel material manufacturers in the world have limited capacity. Such materials have a large gap, expensive import prices, difficult procurement and short supply, which seriously affected the production of ultra supercritical boilers and the development of electric energy in China. At present, China's demand for utility boiler tubes is about tons, and with the continuous improvement of ultra (supercritical) power generation technology, the demand is expanding. Several large domestic enterprises have invested a lot of human and financial resources in the R & D and production of such products, and have made considerable achievements. On the one hand, it has made its own contribution to the development of national electric power industry, but also brought considerable economic benefits to enterprises.The folded stainless steel hot rolled strip is hot rolled into a strip with a thickness of mm-mm and a width of mm-mm.There shall be a special storage rack. The storage rack shall be a wooden or painted carbon steel support or padded with rubber pad to isolate it from carbon steel and other metal materials. During storage, collision with other components purification and damage of iron metal.How much is it,For example, the price of tons of goods = tons = the result example: the price excluding tax of ton of goods = a ton = ~ the total weight of the known coil weight and price = the coil weight price, the thickness of stainless steel plate & Chi; Width & Chi; Long & Chi; e.g. & Chi; Χ Χ = kg stainless steel plate weight per square meter (kg) calculation formula: specific gravity thickness (mm) width (mm) length (m) stainless steel weight per meter (kg) stainless steel pipe calculation formula: diameter (mm) diameter (mm) (correct calculation of the price difference between burr and trimming of nickel stainless steel . chromium stainless steel) in the market, the price difference between burr and trimming of stainless steel is usually set at a fixed price. For example, it is generally considered in the market that the price difference between burr and trimming of is yuan tons and that of is yuan tons. In fact, this method is not scientific. In fact the price difference between burr and trimming of stainless steel is different The correct calculation should be like this.For business people, of course, it is better to spend less under feasible conditions. For goods such as stainless steel pipes, we can often see that there will be packaging film bags on them. Although they are not heavy, if there are a large number of single purchases, they will also produce certain economic expenses, but why do many people clearly dislike this thing on stainless steel pipes, the maintenance of stainless steel pipe should be strengthened in each process of consumption xincoral Xiaobian will tell you why stainless steel pipes need packaging bags.Measures to improve the welding quality of stainless steel pipe in order to ensure that the outer surface of stainless steel pipe is not damaged and purified, mainly including the following three aspects: the processing and consumption of stainless steel pipe should have a special consumption workshop (wood board is well used) , avoid the machining platform of austenitic stainless steel and carbon steel or solid overhead.

. It is our responsibility not to pay attention to the maintenance of the pipe during transportation, mix the pipe with corroded chemical commodities, or soak the two water into the packaging film during transportation in rainy days, which will cause rust. . It is the responsibility of the processor and manufacturer. When cutting stainless steel or iron when manufacturing goods,Port Abbas600 stainless steel plate,Port Abbas2205 stainless steel plate, the scrap iron will cause rust on the surface of the steel pipe. Therefore, it is only reasonable for highly skilled technicians to deepen investigation and discussion, make a reasonable division of responsibilities, and who should be responsible for whose achievements. You can't let steel mills, pipe factories, processors, or users bear the liability for compensation!resources,This material without titanium and niobium has an inherent tendency of intergranular corrosion. Intergranular corrosion can be reduced by adding titanium and niobium and stabilizing treatment. It is a kind of high alloy steel that can corrode in air or chemical corrosive medium. Stainless steel has beautiful surface and good corrosion resistance. It does not have to undergo surface treatment such as color plating to play a role of rust freeAccording to the steel structure, austenite ferrite ferrite martensite and precipitation hardening note: precipitation hardening (precipitation strengthening): refers to a heat treatment process in which the metal is hardened by the segregation zone of solute atoms in supersaturated solid solution and / or the desolved particles are dispersed in the matrix. For example, austenitic precipitated stainless steel can obtain high strength by precipitation hardening at ~ ℃ or ~ ℃ after solution treatment or cold working. That is, the supersaturated solid solution of some alloys is placed at room temperature or heated to more & amp; gt;& amp; gt;Crimping: during crimping, the convex part of the pipe fitting is placed in the concave groove of the die, and the jaw is perpendicular to the pipe axis.Port Abbas, Series & mdash; martensitic precipitation hardening stainless steel pipe.Combined steel and spring steel, (C content is expressed in ten thousandths).Low temperature embrittlement of stainless steel pipe --- in low temperature environment, the deformation energy is small. In low temperature environment, the phenomenon of reduced elongation and area shrinkage is called low temperature embrittlement. It is mostly produced on the body centered cubic structure of ferrite series.