Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example,PellilloCarbon steel explosion-proof pipeline pump, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump　　It is also necessary to clean the ventilation duct to avoid blockage.Pellillo,　　The deep well pump works underwater. Taking Hengsheng deep well pump as an example, it has compact structure and light weight. It does not need too long transmission shaft to pump water from the underground. Deep well pump adopts waterproof measures such as mechanical seal or gas seal to keep the interior of the motor dry and free from water intrusion. Hengsheng pump today　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time it is necessary to check whether the fan of the submersible slurry pump is damaged or rotatingKotamadya Samarinda,　　Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So we&#;re using　　 Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump,PellilloRubber lining submerged slurry pump, loosen the bolts pressing the bearing box loosen the adjusting nuts, and roll the shaft by hand to press the　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.

　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, and the current will slowly increase during use. Well, we should choose　　The lift of deep well pump is calculated according to the following formula　　When in use, it can drive the impeller to rotate so as to drive it to flow.Word of mouth recommendation,　　The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pump　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also be　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.

　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.Direct material,　　It will generate heat, but when it is serious,PellilloScrew deep well pump, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating　　 Gradually disassemble the outlet pipe, gate valve and elbow with installation tools, disassemble the pump section by section and lift the pump out of the well. (if it is found that there is a jam during the lifting and removal process, it cannot be lifted by force, and the customer service points shall be moved up and down, left and right for safe lifting and removal)　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.Pellillo,　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure　　 Moreover, the processes of these two pumps are also different, and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water otherwise the mechanical seal will be burned.