What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC/ models, first install the suspension cage before installing the drive plate).The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, the faster the lifting speed.Rostock,Now we have an increasing demand for cargo elevators. Let me introduce the maintenance work of guide rail cargo elevators to you. When we use a guide rail elevator in our daily life, we need to regularly inspect, maintain, and maintain it. This not only extends the service life of the guide rail elevator, but also makes it more powerful when working! For example, the transmission part should have sufficient oil, and vulnerable parts must be regularly inspected,RostockDouble fork hydraulic lifting platform, or replaced. Mechanical bolts, especially parts that frequently vibrate, such as slewing bearings and lifting arm connecting bolts, should be checked for looseness. If there is looseness, it must be tightened or replaced immediately. Below is an introduction to the steps of maintenance: important maintenance work for guide rail elevators. Regularly check the tire pressure and bearing condition of the guide rail elevators to ensure they are in good condition; Regularly check whether the structure of the bracket and panel is in good condition, once a month; Vulnerable parts must be regularly inspected, repaired, or replaced. Parts that frequently vibrate, such as bolts and slewing bearings, should be checked for looseness. If there is looseness, it must be tightened or replaced immediately.What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.Kirikkale,Carefully prepare a special construction plan for installation and provide technical disclosure to the installation personnel. Our company has been engaged in various types of scissor lift manufacturers and other materials for years, and operates with integrity. Welcome to call!Loose motor fixing screws: When the motor fan rotates, there is a sound. If the screws fixing the motor are loose, coupled with the vibration of the motor itself, the motor collides with other components, resulting in a sound; The joints of each pin shaft are dry, lacking oil, and there is hard friction between the iron parts, which not only damages the components but also produces abnormal noises. Therefore, the editor should emphasize again that timely maintenance and frequent refueling are important; If the hydraulic lifting platform does not rise, there is air in the hydraulic oil. You can open the exhaust hole, add gas, and then tighten it again; Hydraulic oil solidification: replace the hydraulic oil; Oil leakage: Check if there is any oil leakage at the interfaces of each oil pipe. If there is any oil leakage, replace it in a timely manner; Motor reversal: Check for wiring errors; (Manufacturers of hydraulic lifting platforms who do not understand electricity in a timely manner)The application scenarios of mobile elevators may require several or even dozens of passenger elevators in some office buildings and hospitals. In order to increase the speed, efficiency, and usable area of electric elevators,RostockHydraulic lifting platform and hydraulic lifting platform, with each group responsible for a portion of the floors and make different adjustments and scheduling based on the usage mode of different floors at different times.

Talking about the daily maintenance and use of hydraulic lifting platform motors. Overloading is strictly prohibited, as overloading can increase the burden on the motor and in severe cases, cause the motor to burn out.A sign of slowing down has occurred. After the speed slows down, consider the hydraulic oil flow rate first. The factors that affect hydraulic oil flow include: hydraulic pipelines, hydraulic valves, hydraulic oil pumps, motor speed control assembly, etc. The following editor will introduce to you the four reasons for the slower speed and the mediation methods.Maintain a smooth access road for external construction elevators and sufficient parking space for equipment. When using a crane for auxiliary installation, full consideration should be given to whether the on-site environment meets the operating conditions of the crane.Welcome calls ,Remove and disassemble the hydraulic lift cargo elevator lowering valve, blow out the plunger with compressed air, then install it and reinstall it.Elevators are now very popular among people and can easily transport goods to high-rise buildings. Among them,RostockDouble fork hydraulic lifting platform, hydraulic elevators are more popular among people, and people can choose the one that suits them according to their actual situation. However, during normal work, it is important to pay attention to the lifting speed of hydraulic elevators and avoid making mistakes. So what factors will affect the lifting speed of hydraulic elevators?Loose motor fixing screws: When the motor fan rotates, there is a sound. If the screws fixing the motor are loose, coupled with the vibration of the motor itself, the motor collides with other components, resulting in a sound; The joints of each pin shaft are dry, lacking oil, and there is hard friction between the iron parts, the editor should emphasize again that timely maintenance and frequent refueling are important; If the hydraulic lifting platform does not rise, there is air in the hydraulic oil. You can open the exhaust hole, add gas, and then tighten it again; Hydraulic oil solidification: replace the hydraulic oil; Oil leakage: Check if there is any oil leakage at the interfaces of each oil pipe. If there is any oil leakage, replace it in a timely manner; Motor reversal: Check for wiring errors; (Manufacturers of hydraulic lifting platforms who do not understand electricity in a timely manner)

The seat belt needs to be inspected every six months, with a load of kilograms. The test time is five minutes. After the test check whether the seat belt is broken or deformed, and keep records of the experiment. Any unqualified seat belts should be immediately stopped from use.Customer first,After entering winter, elevators are prone to some small problems and malfunctions, which requires users to perform seasonal maintenance and upkeep on the elevator. Below, the editor will briefly introduce the winter maintenance precautions and key points of the elevator.During the use of hydraulic elevators, there will always be problems. Many customers have reported that hydraulic elevators sometimes cannot be lifted. If the hydraulic lift pump can continue to work, other issues need to be considered. Below, the editor will explain the reasons for the hydraulic lift pump station not being oiled and solve the reasons for the hydraulic lift pump station not being oiled, as well as the solutions for mobile elevators The analysis of the pump station of hydraulic elevators such as guide rail elevators is as follows: the motor power supply is abnormal or reversed; The solution is to correctly connect the motor power supply or adjust the steering mailbox to ensure there is no hydraulic oil or insufficient oil; The solution is to add hydraulic oil.Operating cost advantage: Low failure rate. Due to the use of advanced hydraulic systems and good methods, the failure rate of elevator operation can be minimized. Low power consumption: When the hydraulic elevator descends, it is driven by the pressure generated by its own weight, which greatly saves energy.Rostock,What are the pressures on lifting platforms? The movement of lifting platforms has always been a concern for us. Our usage scenarios are uncertain, and most of them are part-time workers. Therefore, in order to better attract customers, we are constantly researching mobile lifting platforms to meet different needs. However, for some large logistics companies or enterprise processing plants, we are still accustomed to using fixed elevators, He has a huge load capacity and strong stability, which can meet the needs of many customers which is also the use of lifting platforms in China in recent years.Although lifting cargo elevators have good safety, if we do not pay attention to detailed maintenance, accidents may occur. Therefore, we should pay attention to them when performing daily maintenance.Any product always has a break-in period when it is first used, so what precautions should we pay attention to during the break-in period when using a hydraulic lifting platform? Today the editor will share this topic with everyone.