JotburBaigang deep well pump,

　　In addition to the method, materials shall be selected comprehensively according to the nature of corrosive medium,JotburWQ submersible pump parameters, anti cavitation theory, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life, protection should be done well which should be a comprehensive optimization design method.　　If the oil seal ring of the shaft is seriously worn, replace it with a new one.Jotbur,　　Work to prevent the electric pump from overheating and damage. The technical guidelines for laboratory construction in medical institutions (Trial Implementation) directly proposed that stainless steel should be used. Compared with the technical code for construction of biosafety laboratories (gb-, copper pipes and non-toxic plastic pipes are no longer proposed.　　During adjustment, firstly loosen the support cover, then compress the nut, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationTyre,　　The packing seal, auxiliary impeller seal and mechanical seal are mainly used. Among them, the packing seal needs small leakage and is not suitable for transporting toxic, corrosive and precious liquids; The sealing of the auxiliary impeller relies on the reverse pressure of the two sealing impellers during rotation to prevent the leakage of the medium, and can also play a role in　　The hardened mud layer collapses after softening avoiding the phenomenon of burying the pump during use.　　Rate.

　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,　　 There are many reasons for motor overheating. It may be because the power supply voltage is too high, or there is a problem with the water pump or the motor itself.　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choicePotential development,　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.　　How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the circulation in the slag slurry pool is basically unchangedquality,　　What is the cause of pump overload.　　The specific treatment methods are as follows: first, check the power supply of the power supply to see whether the connector of the power supply is secure whether the switch is tight, and whether the fuse is intact. In case of short circuit, short circuit, fuse burnout and other problems, it shall be repaired in time. If it is not a power problem, check the water pump　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.Jotbur,　　How to avoid this situation when the equipment is in use.　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand,JotburSubmersible sewage pump, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.