Good ductility, used for forming products. It can also be machined to harden rapidly. Good weldability. Wear resistance and fatigue strength are better than stainless steel.The back is not protected by argon, and the flux cored wire + TIG process has been applied in China for several years. Flux cored wires such as et-elt-et-elt-t-et-elt- have been produced and applied to field welding, and good economic benefits have been obtained.Yara,Stainless welded pipe (grade y) gb- stainless cold plate (grade I)Austenitic stainless steel austenitic stainless steel is developed to overcome the lack of corrosion resistance and brittleness of martensitic stainless steel. The basic composition is crl% and Ni%, which is referred to as - steel for short. Its characteristic is that the carbon content is less than .%, and the single-phase austenite structure is obtained by the combination of Cr and Ni.Choma,The shape of pipe end stainless steel pipe can be divided into smooth pipe and threaded pipe (threaded steel pipe) according to the state of pipe end. Threading pipe can also be divided into ordinary threading pipe (pipe for conveying low pressure such as water and gas, which is connected by ordinary cylindrical or conical pipe thread) and special threaded pipe (pipe for petroleum and geological drilling, which is connected by special thread for important threading pipe). For some special pipes, in order to make up for the impact of thread on the strength of pipe end, the pipe end is usually thickened before threading (inner thickening, outer thickening or inner and outer thickening).The bright nickel layer on the stainless steel pipe is a silver white metal with slight yellow light. Its hardness is higher than that of copper,YaraStainless steel 304H plate, zinc, tin, cadmium, gold and silver, but lower than that of chromium and rhodium. Bright nickel has high chemical stability in air and good stability to alkali. Using Brightener on stainless steel pipe, bright nickel can be directly plated without polishing,YaraSpecification of stainless steel square pipe, so as to improve the hardness, wear resistance and leveling of the surface, make the appearance of stainless steel pipe consistent with other nickel plated parts, and avoid the corrosion of potential difference between stainless steel pipe and other bright nickel. After using bright nickel solution for a period of time,YaraStainless steel pipe, and there is a large demand for building water supply pipes. According to the 'Ninth Five Year Plan' of construction and the outline of long-term objectives in , the demand for each pipe is ~ km from to , including km of cold and hot water pipes in residential construction areas. Some people believe that the development of stainless steel water pipes is of great significance to improve the grade of modern urban buildings.

Pipeline direct drinking water has developed rapidly. With the development of national economy, pipeline direct drinking water has developed rapidly in domestic cities such as Beijing Shenzhen, Shanghai and Chongqing, and economically developed medium-sized cities have also actively planned to catch up. In direct drinking water, domestic high-grade hotels and public places have been equipped or are equipped with direct drinking water pipes.Tax included: the invoice contains % tax, so it will also affect subsequent quotations.The shape of pipe end stainless steel pipe can be divided into smooth pipe and threaded pipe (threaded steel pipe) according to the state of pipe end. Threading pipe can also be divided into ordinary threading pipe (pipe for conveying low pressure such as water and gas, which is connected by ordinary cylindrical or conical pipe thread) and special threaded pipe (pipe for petroleum and geological drilling, which is connected by special thread for important threading pipe). For some special pipes, in order to make up for the impact of thread on the strength of pipe end, the pipe end is usually thickened before threading (inner thickening, outer thickening or inner and outer thickening).how much,Ferritic and martensitic stainless steels are represented by series numbers. Ferritic stainless steel is marked with and , martensitic stainless steel is marked with and C, dual phase (austenite ferrite).Model & mdash; High strength cutting tool steel, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It belongs to hard stainless steel. A common application example is & ldquo; Shaving blade & rdquo;. There are three common models: C and f (easy to process).Marking: in order to make the steel pipe complete the socket of the pipe fitting, the length must be marked and marked at the pipe end.

Model & mdash; Commonly used precipitation hardening stainless steel model usually also called -; %Cr,%Ni.Latest quotation,When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the welding speed, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.In the grades of Japanese steel (JIS Series), ordinary structural steel is mainly composed of three parts, which represent the material, such as s (steel) represents steel and f (ferrum) represents iron; The second part represents different shapes, types and uses, such as P (plate) represents plate, t (tube) represents tube, and K (kogu) represents tool; The third part represents the characteristic number, which is generally low tensile strength. For example: SS & mdash& mdash; One s represents steel, and the second s represents & ldquo; Structure & rdquo; (structure), is the lower limit tensile strength of MPa, and the whole represents ordinary structural steel with tensile strength of MPa. & mdash; high strength cutting tool steel, with slightly higher carbon content, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It is one of the hard stainless steels. A common application example is & ldquo; shaving blade & rdquo;. There are three common models: C and f (easy processing type).Yara,Household worries.Duplex stainless steel product description: This stainless steel has good corrosion resistance in urea carbamate solution and high stress corrosion cracking resistance in chloride environment. At the same time, the duplex stainless steel has excellent mechanical properties and can be used in plant construction with high safety requirements.Assembly: the sealing ring shall be correctly installed in the U-groove of the pipe fitting, put the pipe into the socket of the pipe fitting and wait for crimping.