In this case, it is necessary to check all the wires and cables used frequently to ensure that they are not damaged. When there is bandaging or damage, the parts must be replaced in time. I believe that many people have encountered the phenomenon of overheating of the motor. In this case, it is necessary to stop in time, so that the motor shaft can run smoothly and the effect is good.With the above detailed introduction, I believe that everyone has a comprehensive understanding and understanding of the use of hydraulic lifts, and these details cannot be ignored in the process of use.NIM,The power supply needs to be disconnected during the resistance check. At this time, the principle can be used to measure, and then the resistance value can be measured, so that the fault point can be analyzed accordingly. These introductions, I believe you have mastered a lot of basics.Even Yehuda,In this case, it is necessary to check all the wires and cables used frequently to ensure that they are not damaged. When there is bandaging or damage, the parts must be replaced in time. I believe that many people have encountered the phenomenon of overheating of the motor. In this case, it is necessary to stop in time, and then continue to use it after troubleshooting, pay attention during use to prevent damage to hands, feet and clothes.To understand the operation of the mechanism, it mainly depends on whether it is normal and whether there is noise during use. When a fault is found, it needs to be eliminated in time, so as to ensure the normal operation and use of the machine. It is usually necessary to disassemble or adjust the slewing mechanism during installation. In this case, it is necessary to ensure that the centerline of the slewing mechanism on the reducer is parallel to the centerline of the gear, and of course the meshing clearance must be appropriate. If this is not appropriate, then the machine will not work properly.

At the same time, pay attention during use to prevent damage to hands, feet and clothes.When using a hydraulic lift, check the connection of each part during use, and tighten it in time if there is any looseness. All the connecting shafts need to use cotter pins the purpose is to be able to fully meet the needs, and then can be used better.Let's see,The power supply needs to be disconnected during the resistance check. At this time, the principle can be used to measure, and then the resistance value can be measured, so that the fault point can be analyzed accordingly. These introductions, I believe you have mastered a lot of basics.When the hydraulic lift is in use, it must have a corresponding inspection route. If the route fails and the joint is loose, then in this case it needs to be switched or the point is not good. In this case, it will appear. Short circuit or damaged components. It is relatively better to use a table to check.To understand the operation of the mechanism, it mainly depends on whether it is normal and whether there is noise during use. When a fault is found, so as to ensure the normal operation and use of the machine. It is usually necessary to disassemble or adjust the slewing mechanism during installation. In this case, it is necessary to ensure that the centerline of the slewing mechanism on the reducer is parallel to the centerline of the gear, and of course the meshing clearance must be appropriate. If this is not appropriate,NIMSelf elevating platform vehicle, then the machine will not work properly.

The power supply needs to be disconnected during the resistance check. At this time, the principle can be used to measure, and then the resistance value can be measured, so that the fault point can be analyzed accordingly. These introductions I believe you have mastered a lot of basics.Executive standard,To understand the operation of the mechanism, it mainly depends on whether it is normal and whether there is noise during use. When a fault is found it needs to be eliminated in time, so as to ensure the normal operation and use of the machine. It is usually necessary to disassemble or adjust the slewing mechanism during installation. In this case, it is necessary to ensure that the centerline of the slewing mechanism on the reducer is parallel to the centerline of the gear, and of course the meshing clearance must be appropriate. If this is not appropriate, then the machine will not work properly.With the above detailed introduction I believe that everyone has a comprehensive understanding and understanding of the use of hydraulic lifts, and these details cannot be ignored in the process of use.NIM,NIMAircraft container dedicated lifting platform vehicle,NIMAircraft lifting platform vehicle,To understand the operation of the mechanism, it mainly depends on whether it is normal and whether there is noise during use. When a fault is found, it needs to be eliminated in time, so as to ensure the normal operation and use of the machine. It is usually necessary to disassemble or adjust the slewing mechanism during installation. In this case, it is necessary to ensure that the centerline of the slewing mechanism on the reducer is parallel to the centerline of the gear, then the machine will not work properly.When the hydraulic lift is in use, it must have a corresponding inspection route. If the route fails and the joint is loose, then in this case it needs to be switched or the point is not good. In this case, it will appear. Short circuit or damaged components. It is relatively better to use a table to check.When using a hydraulic lift, check the connection of each part during use, and tighten it in time if there is any looseness. All the connecting shafts need to use cotter pins, the purpose is to be able to fully meet the needs, and then can be used better.