Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore,NorfolkBody guide rail type cargo elevator,NorfolkElevating cargo elevators require, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.Norfolk,Improper use of oil: Inadequate maintenance of mobile lifts and other high-altitude work platform equipment will cause the fitting clearance of parts to be small, and the oil is not easy to form a uniform oil film on the friction surface. In addition, due to assembly and other reasons, it is difficult to ensure the uniformity of the fitting clearance. Thereby reducing the efficiency and causing early abnormal wear of equipment parts; in severe cases, it will cause scratches or bites on the precisely matched friction surfaces, resulting in abnormal noise of the equipment.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Lampang,In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, and the contact arc crater should be polished in time.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.

Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform no one should stand around to watch.Based on the information you have investigated, choosing a lifting machine with better cost performance should be based on its technical parameters, practicability and versatility. Usually, there are many kinds of aluminum alloy lifting machines, including vehicle-mounted lifts, fixed lifts, hydraulic lifts, etc. Lifting platforms scissor lifts, etc. each have slightly different technical parameters and uses but there are also many similar functions. Therefore, as a customer, you have to choose with a purpose, that is you buy a mechanical lift What to do, when unpacking and accepting, check whether the accompanying technical information is complete, whether the accompanying accessories, tools, and accessories are consistent with the list, and whether the equipment and Check whether the accessories are damaged, defective, etc., and make a record of unpacking and acceptance. The working principle of the aluminum alloy elevator: the hydraulic oil is formed by the vane pump to a certain pressure, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the hydraulic cylinder The upward movement of the cylinder lifts the heavy object, and the oil returned from the upper end of the hydraulic cylinder returns to the fuel tank through the explosion-proof electromagnetic reversing valve. The rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.Click to view,Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.The water cooling of the hydraulic station is generally tube-type water cooling,NorfolkLifting cargo elevator, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.

Avoid working in an environment. In the event of rain, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Quality inspection report,It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Today, the temperature in Shandong suddenly dropped, catching office workers and the public by surprise. Dear friends, you must remember to add more clothes when you go out. Shandong is the hometown of elevators in China. There are countless large and small manufacturers. So, how to maintain the lifting stage and the elevator after entering the winter. Below is a detailed introduction for you.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Norfolk,The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.