Plan scheme : for high carbon steel with carbon content of more than .% and high chromium alloy pipe with chromium content of no less than %, the interval is min.Because alloy pipe is a very unique pipe fitting, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, when installing alloy pipes, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.Isfahan,The multi-al combination of reinforcement mesh welding machine and reinforcement mesh row welding machine based on PLC basic control. At present, the full-automatic mesh welding machine has the characteristics of simple operation, high control precision and easy to master the process of high-speed continuous welding.According to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W IX and iy are not as good as H-section steel under the premise of equal weight.Hwado,H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.→ wide flange and large lateral stiffness. Strong bending resistance.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation,IsfahanReinforcement material list, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.

The flange of H-beam is of equal thickness including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section. Spiral seam high-frequency welded steel pipe (sy- for general low-pressure fluid transportation takes hot-rolled steel strip coil as pipe blank and is often spiral formed at warm temperature. High frequency lap welding method is selected for welding spiral seam high-frequency welded steel pipe for general low-pressure fluid transportation. Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, the negative rolling method can be used Spread rolling, etc.management, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.I-beamWhen it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.

Frame line crackProduct survey, Remove defective pipes within the allowable length.Filling: welded pipe is welded by electric welding of hot-rolled strip steel, so its influence was not as high as that of seamless steel pipe.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment,Isfahan09CrCuSb alloy pipe, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation,Isfahan6. How many kilograms per meter of sub welded pipe, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Isfahan,Whether I-section steel is ordinary or light, due to the relatively high and narrow section size there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, which makes it very limited in the scope of application.All the cracks occur at -mm away from the edge below the alloy pipe it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.Heating surface pipes, economizers, superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)