Ensure good power supply at the installation site, install a separate distribution box,XinqiuCargo elevator, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)XinqiuApplication scenarios of mobile elevators Some office buildings and hospitals may need several or even dozens of passenger elevators. In order to increase the speed, efficiency and building area of ​​electric elevators,XinqiuElevator goods ladder, most high-rise buildings will divide electric elevators into groups. Each group Responsible for some floors, and make different adjustments and scheduling according to different time and usage patterns of different floors.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, quality guaranteed!Silang,It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load,XinqiuChain guide rail lifting cargo elevator, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, the editor will simply popularize the knowledge for everyone.The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.

The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, which increases the copper loss of the winding, causing the winding to overheat and even burn out.The sinking of the freight elevator is the phenomenon that after a certain period of time, the platform will drop due to gravity after rising to the designated position. Of course, this kind of problem must be abnormal, so how to solve it? The first is to find the reason, and the following editor summarizes the ultimate solution.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .The cost is reasonable,The load of this series of products is divided into . to . tons, with a load of up to tons.In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .

It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Where to sell API, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission it can be divided into two types: open type and closed type. Of course, and the oil is not easy to form a uniform oil film on the friction surface. In addition the lift also has a lot of safety equipment.Improper use of oil: Inadequate maintenance of mobile lifts and other high-altitude work platform equipment will cause the fitting clearance of parts to be small, due to assembly and other reasons, it is difficult to ensure the uniformity of the fitting clearance. Thereby reducing the efficiency and causing early abnormal wear of equipment parts; in severe cases, it will cause scratches or bites on the precisely matched friction surfaces, resulting in abnormal noise of the equipment.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Xinqiu,Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.