Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to　　 The fan speed of the water pump is too low, so the heat cannot be dissipated.Faroe Islands,　　The pipeline support is unstable and shakes.　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.Kyela,　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use　　Other ysts believe that,Faroe IslandsSelf priming non clogging sewage pump, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especially　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.

　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulation　　This can ensure that the water pump has been running at the best operating point, which not only meets the process needs,Faroe IslandsScrew deep well pump, but also reduces the equipment loss, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pumpFree consultation,　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature high pressure and low temperature.　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, it means that the pump is full　　Submersible slurry pump In addition, the sewage pump is usually driven by a motor which also requires some time og quantity when switching on and off, so in fact, it can be adjusted to a certain extent during use. The submersible slurry pump needs to use a line when in use

　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motorEnergy costs,　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper, feeler gauge, square ruler, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn, etc.　　 The reasons for excessive power loss are as follows: the running speed of the screw rod is too high.　　Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil liquid metal, acid-base night and so on. It is a good means of transport.Faroe Islands,Faroe IslandsDrilling fluid slurry pump,　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.　　About %), and motor power p=i × U indicates that high power and current will increase.　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.