It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф . Anchor bolt structure for M assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. The platform is based on&quo; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates,Frankfurt on mainHydraulic mobile boarding bridge, and can withstand a speed of kilometers/hour when the forklift is fully loaded without bending, improving work reliability.The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.Frankfurt on main,Adopting anti slip patterned steel plates, the platform has good anti slip performance.Once again whether the site selection, pit design, and installation are in place, as well as whether there is construction, will affect the service life and safety of the fixed hydraulic boarding bridge.Morogoro,Its design is usually fully standardized as early as the structural design of buildings.Insufficient understanding of the operating conditions of the axle. Assuming you understand some fundamental principles and the three elements that lead to success you can ensure that you are in excellent working form for a long time. Inspection before use of mobile boarding bridge: Check if the oil unloading valve is tightened. Use of mobile boarding bridge: Use a hand pump to raise the boarding bridge to the required position and height; Place the tongue plate on the box and connect the safety chain to the box; Place the wheel mask in a suitable position next to the tire; Release the manual oil unloading valve to make the oil cylinder and wheels in a natural state, making them in a relaxed state; After the above preparations are completed, loading and unloading can begin; Precautions for operation: Keep the oil cylinder in a relaxed state during use; Both electric and manual lifting must turn off the manual pump switch.The instrument equipment instrument inspection (inspection and testing) method utilizes various instruments to measure the hydraulic system, parameters, and analyze and process these data (ch ǔ l ǐ) To determine the location of the fault. A mature lifting platform manufacturer in China, with complete products and quality assurance.

It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф . Anchor bolt structure for M assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. The platform is based on&quo; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of kilometers/hour when the forklift is fully loaded without bending, improving work reliability.Firstly, before using the equipment (shè bè i), it is necessary to check whether there is water accumulation in the points, and then confirm whether the fasteners are damaged or loose. If a fault is detected, necessary repairs and replacements need to be carried out. Check all control devices (zhu ā ng zhì） Whether the operation is normal, whether the switch and governor are in good condition, and whether the display is normalThe hydraulic boarding bridge is mainly made of anti slip thick steel plates during the production and manufacturing process, and all equipment can provide good anti slip characteristics to a certain level in operation and application. The hydraulic press loading bridge is a specialized auxiliary equipment that maintains rapid loading and unloading of goods. Its height adjustment function creates a bridge between the large truck and the cargo platform in the warehouse. Transport vehicles such as electric forklifts can immediately enter the large truck to carry out mass loading and unloading of goods, the device can loosen the return valve button during the lowering process, thereby reducing the weight of the device.wholesaler,The fixed boarding bridge of the service platform is immediately installed on the outer edge of the unloaded service platform during the entire installation process. When applied, there is no need to excavate or pre bury the indoor space of tunnel construction on the loading and unloading platform, and most of the buildings do not need to be modified in terms of structure.In general, there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder, etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes, sand holes, and shrinkage porosity in the guide sleeve.Insufficient understanding of the operating conditions of the axle. Assuming you understand some fundamental principles and the three elements that lead to success, you can ensure that you are in excellent working form for a long time. Inspection before use of mobile boarding bridge: Check if the oil unloading valve is tightened. Use of mobile boarding bridge: Use a hand pump to raise the boarding bridge to the required position and height; Place the tongue plate on the box and connect the safety chain to the box; Place the wheel mask in a suitable position next to the tire; Release the manual oil unloading valve to make the oil cylinder and wheels in a natural state, making them in a relaxed state; After the above preparations are completed, loading and unloading can begin; Precautions for operation: Keep the oil cylinder in a relaxed state during use; Both electric and manual lifting must turn off the manual pump switch.

Vibration acoustic method: Vibration acoustic instruments detect the vibration and noise of hydraulic systems, and identify the wear (a basic type of component failure) and technical status of hydraulic components according to the laws of vibration acoustics. Based on this diagnose the cause, location, degree, nature, and development trend of faults. Nowadays, with the rapid development of the logistics industry, the demand for logistics equipment is becoming increasingly weak, and auxiliary improvements such as fixed hydraulic boarding bridges and fixed lifting channels, as well as the increase in loading and unloading equipment usage, have been made. Some manufacturers have now achieved export to foreign countries!original,Frankfurt on mainHydraulic boarding bridge mobile type,Once again, whether the site selection, pit design, and installation are in place, as well as whether there is construction, will affect the service life and safety of the fixed hydraulic boarding bridge.Assuming that the manufacturing quality of fixed hydraulic boarding bridges is not satisfactory, the reasons for their shortcomings are mostly preventive repairs, and there are usually fewer elements of abnormal operation.In general, there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder, etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes, sand holes, and shrinkage porosity in the guide sleeve.Frankfurt on mainOf course, due to frequent shipments, long operation time, and large carrying capacity, the quality of fixed hydraulic boarding bridges has been greatly tested. Based on market analysis, the editor above provides some suggestions to enemies who have used fixed hydraulic boarding bridges, and pays attention to some achievements in the application process.When using the boarding bridge for loading and unloading, load and unload according to the rated load, and do not be overweight. If overweight occurs, it will make the hydraulic system struggle during the lifting process, and even cause deformation of the hydraulic cylinder body, the only option is to replace it with a new one.Firstly such as Shanghai Niuli Machinery. If the deformation is severe, there are certain strict requirements for the quality and material selection of height adjustment plates to avoid the occurrence of defective materials, which will result in unexpected loss of performance in the application process.