H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, unique and convenient installation and reduce the construction cycle time of the project. On the whole,When excavating a tunnel in a stratum where the rock is not hard and complete it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Belville, it is generally necessary to excavate a diversion pit (also known as pilot hole) and set temporary support. Peak crackSaceleAlloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.Key technical characteristics of alloy pipe: The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.

At present, there is still a big gap in the production technology of C-section steel between China and foreign countries.First,Belville20 alloy pipe, the wall thickness of high-quality and smooth steel is particularly thick. Because the thicker the wall thickness of the product, the greater the processing cost and opportunity, and the higher the resource cost. Secondly, the process of smooth steel also determines its limitations. Generally, smooth steel has low precision, uneven wall thickness, low brightness inside and outside the pipe, high length cost, pockmarks in the internal appearance, and black spots are not easy to remove. Again, the inspection and shaping need to be processed offline. Therefore, it has its advantages in high pressure, high strength and mechanical structure materials. In the process of use, we will gradually find out. In fact, seamless pipe has also entered the market in recent years. With the growth of market demand, the advantages of seamless pipe have also been stimulated. But there are also many fakes and fake products on the market. Be careful when you choose.After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution, ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.Process inspection,What is the stainless steel passivation of alloy pipe?After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.I-beam is widely used

The wear resistance, fracture toughness, impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.Executive standard,Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main sleeves of the section is quite different which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings. Pipe installationThe shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Belville, in leg width and in waist thickness. Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings,BelvilleHow much is No. 14 I-beam,BelvilleHow much is the price of q355b I-beam per ton, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded. Remove defective pipes within the allowable length.