: it refers to the processing of square tube,negotiationGalvanized 40 square pipe,negotiationPrice list of galvanized rectangular pipe, which places metal in a closed Jane and applies pressure at the end to extrude the metal from the specified die hole to obtain finished products with the same shape and size. It is mostly used to produce non-ferrous metal materials. Square tube ferrous metal, steel and non-ferrous metal. Before introducing the classification of steel, briefly introduce the basic concepts of ferrous metal, square tube steel and non-ferrous metal.The square tube for fluid transportation (gbt-) is a general square tube for transporting water, oil, gas and other fluids.negotiation,The calculation method theory of square tube mechanics is feasible to calculate static structures, such as warehouses, houses and bridges, but it is not suitable for moving components such as wheels. At this time, people often use the plastic theory. The research of the plastic theory can be traced back to . In , the European Design Association formulated D plastic design code, the requirements are as follows:% sigma; B% sigma;% zeta;% ge;% delta;% ge; % for high-rise buildings, the allowable stress is usually calculated according to the safety factor that the allowable stress is not less than the dynamic load and multiplied by the allowable stress. In the case of bending of an axis, the formula a = w can be used Using plasticity instead of calculated strength can improve the bearing capacity of members by %.Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn Q, etc.Gokwe,Hundreds of degrees Celsius, which can save energy.Hardness QB square hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Forging square tube: a kind of pressure processing in which the reciprocating impact force of the forging hammer or the pressure of the press changes the blank into the shape and size we need. It is generally divided into forging and die forging. It is often used to produce large-scale materials and materials with large square tube size.

C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.For the level of resistance welding cold formed square pipe, the size of R angle is generally between - times of the wall thickness. It can also produce R angle square pipe of the size required by customers according to customers' needs; Square pipe is a kind of long steel with hollow section and no joints around. It is a square pipe formed by four sides of seamless pipe mold. Square pipe has hollow section, professional square pipe, square rectangular pipe seamless square pipe, galvanized square pipe, galvanized square pipe, strict inspection and quality assurance. The preferential activity is in progress. Welcome to consult. A large number of pipes are used for conveying fluid. They are mainly used in conveying hydraulic support and mechanical structure, Medium and low pressure, high pressure boiler tubes, heat exchange tubes, gas, oil and other industries. It is stronger than welded and will not crack.It is the process of drawing the die hole of the rolled metal blank (shape, pipe, product, etc.) into a section to reduce the length and increase. It is mostly used for cold processing.Project scope,Forging square tube: a kind of pressure processing in which the reciprocating impact force of the forging hammer or the pressure of the press changes the blank into the shape and size we need. It is generally divided into forging and die forging. It is often used to produce large-scale materials and materials with large square tube size.According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.The appearance of fake and inferior square tubes often has pitting. Pockmarked surface is an irregular uneven defect on the surface of square lead pipe due to serious wear of rolling groove. Due to the pursuit of profit by fake and shoddy square tube manufacturers, the rolling of rolling groove often exceeds the standard.

The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out,negotiationGalvanized pipe size specification table, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.Job description,The other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.It is forbidden to degrease the oil square pipes and pipe fittings in the direct production concentration unit, air separation unit, oil refining and chemical engineering according to the design requirements. The purpose of degreasing is to prevent the transported or stored materials from being contaminated by grease or organic matter; Avoid mixing transported or stored materials with grease or organic matter; Oil content to ensure the activity of the catalyst; The content of oil and organic matter to ensure the purity of the product. The installed square pipe shall be disassembled into pipe sections for degreasing. Pipes that cannot be disassembled after installation shall be degreased before installation. Square pipes with obvious oil stains or serious corrosion shall be cleaned by steam purging, sand blasting or other methods before degreasing.For gas transmission: gas, steam and liquefied petroleum gas.negotiation,When the vehicle is replaced with seamless square tube blank, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.The pipeline is only subject to chemical pickling, which can remove oxide scale, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, and the batch rules shall comply with the provisions of corresponding product standards.