Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well we should choose Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.Major Kabir, To solve this problem, we need to regularly inspect and repair the slurry pump. Our common maintenance methods are as follows: Auscultation: when the submersible slurry pump works normally, the accompanying sound has a certain melody and rhythm. As long as you are familiar with and master these normal melodies and rhythms, you can During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary timesPavlikeni, It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses. Then there are new structures, such as thermohydrodynamic seals, backup seals and asymmetric molded metal single wall bellows seals. After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.
The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing water temperature (maximum) The pump can often be selected according to the specific requirements of lift,Major KabirZD slurry pump, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performancesafety requirements , Rotate in the rolling direction until the friction between the impeller and the front guard plate stops then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment It is located in the middle, so it seems that many regions have good effects when using it. In this way, when the equipment is used again, the solvent in the pump is often less, and the power consumption is also less and the efficiency of the pump in use is often improved, so that the equipment can drive the solid to flow when it is in use and the fact is
Let the medium containing some solid particles generate a certain flow rate, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simpleInterpretation and observation, so it has an irreplaceable position when it is used. What is its own structure when it is used. The delivery flow of screw pump has nothing to do with the delivery pressure. The delivery pressure is only related to the stage of screw pump, while the flow and speed have a strict positive proportional relationship. Therefore, when it is necessary to control the conveying flow, it is only necessary to adjust the motor speed by equipped with frequency converter or realize stepless speed regulation by belt. Carbon, building materials, The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Lets understand briefly. The whole packing body, packing ring and packing,Major KabirAh slurry pump, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min,Major KabirWQ submersible sewage pump, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.