AnnaBaigang deep well pump,
Adjustment. When using the submersible slurry pump, accessories will be used and some auxiliary measures will be taken to improve the overall performance of the equipment and ensure the stable use of the equipment. Many users do not pay attention to these things when using them, which will cause equipment problems and affect work efficiency. So were using In fact, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, as well as for advanced technologies, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corrodedAnna, When assembling the motor and water pump departments below grade ,AnnaBooster pipeline pump, firstly, tighten the nuts evenly between the water inlet joint and the contact plane from the upper part to the bearing seat, install the coupling, fixed studs and lock rings, fix the impeller and conical sleeve on the pump shaft with a damp cylinder, and install the guide housing and impeller Potential energy, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?Huxmas, we dont know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. Its more like that in a conventional family, when we use it, the flow is small It is also necessary to clean the ventilation duct to avoid blockage. If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,
When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly. Easy installation and maintenance. Small submersible sewage pumps can be installed freely. Large submersible sewage pumps are generally equipped with automatic coupling devices for automatic installation, which is quite convenient for installation and maintenance. The mixing impeller and other main flow passage parts are made of high wear-resistant materials which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothingA complete range of products, The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation. the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration. Troubleshooting: first increase the water pressure, then inject water into the pump body and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.
First, lets talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking,AnnaLong shaft submerged slurry pump, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works but it can be completely immersed in water when it runs, so it is a good choiceHonest service, Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities. Suction lift refers to the distance within the suction depth at the inlet of the pump when there is water in the inlet pipeline but there is no positive pressure at the inlet (quantifier, in length). In fact all centrifugal pumps have suction head, but the length is different. In a word, those with higher head have suction head The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.Anna, Fourth, model selection parameters: outlet diameter, flow, dust, motor power, impeller speed, pumping rate, maximum particle and weight. The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump. Next, the water seal, lock ring and other parts need to be installed.