Causes: there is air or gas accumulation in the water inlet pipe of the pump, or the bottom valve is not closed tightly, the water supply is not satisfied, and the gate valve or flap valve is not closed tightly. Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. asAris In addition, for different media pumped by the deep well pump, the pump components can be made of corrosion-resistant materials suitable for various media, such as copper, L and other stainless steel. Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry', which is wear-resistant and particle passing.Slatina, In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines. We also need to limit the starting frequency and select appropriate thermal protection devices for use. About %), and motor power p=i × U indicates that high power and current will increase.
If the submersible slurry pump cannot be installed and operated,ArisCirculating hot water pipeline pump, the blank operation point can be supplemented. The submersible sewage pump operates under water. Compared with other motors,ArisCarbon steel explosion-proof pipeline pump, the working environment is poor. Regular inspection and maintenance are essential to ensure the 'health and longevity' of submersible sewage pumps! We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used, There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications, its application effect will be great Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), outside micrometer, caliper feeler gauge, square ruler, copper bar, screwdriver with handle, hammer V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn, etc. Screw it down, and then remove the bearing inner race,ArisSubmersible sewage pump, O-ring, shaft sleeve and retaining sleeve in turn.
When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.Quality risk, If the hot water within ℃ is recommended the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature. Structural features of horizontal slurry pump: The ah, HH and L-type slurry pumps at the pump head are of double pump shell structure, that is, the pump body and cover are equipped with replaceable wear-resistant metal lining, and the flow passage components such as impeller, sheath and guard plate are made of high chromium wear-resistant metal. The pump body and cover are made of grey cast iron according to the working pressure Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submergedAris, Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now lets talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,