Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .After the goods are transported, clean up the debris on the platform.Lorient theIt has been inspected and debugged, it only needs to be connected to the power supply and all technical indicators have met the design requirements. When using it, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Sagoda,Test the freight elevator every day to see if the freight elevator can operate normally.If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.
The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.Overview of manual hydraulic platform: Manual hydraulic platform is a small lifting mechanical platform mainly used for small-scale lifting,Lorient 3-meter cargo elevator, lifting, moving and placing items, and also for handling small valuables. The appearance of the product is generous and beautiful, the structure is firm, stable, safe and reliable, and its performance and service life have reached the advanced level of the same equipment. At present, the mainstream of the market is hydraulic drive lifting. Due to its small size and convenient movement, it is widely used in logistics transportation, warehouse management, libraries, supermarkets, and ordinary small equipment manufacturing industries.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls rollers, Turntable, steering, with various methods (separate telescopic), linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises,Lorient Chain guide rail lifting cargo elevator, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.Quality riskThe water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .
Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Inspection basis,Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Cleaning and keeping it clean is the first priority. Regularly clean up the dust or sundries on the motor of the hydraulic lifting platform, otherwise the long-term accumulated dust will fall into the motor fan, just like the laptop we usually use. If the dust on the computer fan is not cleaned, the computer will not be easy to dissipate heat, or even buzz. It will be much better after cleaning, and the same is true for the motor of the hydraulic lifting platform. V or V; how to properly maintain the motor of the hydraulic lifting platform to avoid the motor, it is safer to keep away from the water for things related to electricity, do not use it outdoors in rainy and snowy weather, etc., and pay attention to the selection during storage The environment is clean and dry; it is strictly forbidden to overload the hydraulic lifting platform. When using the hydraulic lifting platform,Lorient Two layers of hydraulic lifting cargo elevator, it must not be overloaded, which will bring a burden to the motor and it may burn out the motor; At this time, you may wish to consult the manufacturer about the overload protection device. The overload protection device is generally selected by the manufacturer. After adding this device, you don’t have to worry about whether it is overloaded during use. It is not too expensive to add this device. Safe, more at ease); can not adjust the overflow valve (also known as 'solenoid valve')Outriggers: mechanical outriggers, ordinary hand-operated outriggers, pull-out outriggers.Lorient ,What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.