Small longitudinal crackI-beam, can only be directly used for bending members or lattice members on its Web because of its large and narrow section size and large moment of inertia difference between the two main axes on the section. It is not suitable for axial compression members and flexural members perpendicular to the web plane, so its application range is very limited. I-beams are widely used in buildings and other metal structures.Arcai,The seamless pipe produced by the seamless pipe manufacturer is a long seamless pipe without any joints around and with hollow section. The thicker the wall of this product produced by the manufacturer, the higher the use value and economic value of this product. If its wall thickness is thinner, Secondly, the product technology produced by this seamless pipe manufacturer often determines its limitations.Requirements of alloy tubes for low and medium pressure boilersJakarta,Function of I-beam: where is I-beam mainly used?At present, there is still a big gap in the production technology of C-section steel between China and foreign countries.Alloy tube is widely used in our daily life, which provides us with great assistance.
Judged as failing. As long as the pipe material is high-strength alloy steel, including alloy steel pipes with temperature resistance, pressure resistance wear resistance and low temperature resistance, the welding process shall be focused on preventing the tendency of martensite structure and cracks due to welding high-temperature operation. The general process requirements are that the welding rod shall be selected and baked as required and sent to the welder for use. The oil and water shall be removed before welding on both sides of the weld Rust and sundries shall be removed and cleaned. The welding line energy shall be as small as possible to minimize the swing during the welding process. The arrangement of the last weld shall have annealing effect on the heat affected zone as far as possible. Slow cooling after welding, cover with asbestos cloth, etc.Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite,ArcaiGh3128 alloy pipe, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.Recommendation and consultation,H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, and can save a lot of materials and construction time.I-beam is a long strip steel with groove section, which belongs to carbon structural steel for construction and machinery. It is a section steel with complex section,ArcaiIncoloy800H alloy pipe, and its section shape is groove shape. Chinas imports of I-beams are greater than its exports. The main producing areas are Tangshan Iron and steel, Baotou Iron and steel, Shangang, huangte, Maanshan Iron and steel Xuanhua Iron and steel, Japan iron and steel,ArcaiHow much is 110 galvanized pipe per meter, etc.Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing, siliconizing and so on are commonly used in production.
Advantages of using I-beam: reduce maintenance cost, reduce downtime, improve equipment operation rate, reduce wear, reduce equipment capacity and increase power consumptionRecommendation and consultation, The defects can be removed by grinding with sand wheel but the remaining wall thickness must be within the allowable standard.High percentage of metal strength. Hot push hole diameter. More sensitive applications and facilities of such methods require simplicity, low cost, easy maintenance, durable economic development and convenient product specification transformation. For example, the production of large diameter must be grooved pipe, elbow and similar products. You only need to add some spare parts. The expansion method of hot push can be used to process and manufacture large-diameter, and can not exceed the working capacity of thick wall pipes of machinery and equipment.Arcai,What is the purpose of flat steelH-section steel belongs to high-efficiency and economic cutting profile (other cold-formed thin-wall section steel, profiled steel plate, etc.). Due to the reasonable section shape, they can make the steel give more play to its performance and improve the cutting capacity. Different from ordinary I-type, the flange of H-section steel is widened, and the inner and outer surfaces are usually parallel, so it is convenient to connect with other components with high-strength bolts. Its size composition is reasonable, series and models are complete, which is convenient for settingH-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight and can save a lot of materials and construction time.