Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You dont have to worry about it. Water pump can transport many things, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport. The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, stainless steel, titanium alloy and other materials used in Chinas mining,ShaalisaSelf priming slurry pump wholesale, chemical and water conservancy projects on the Yellow River are prone to wear, For /g-g gravel pump, which belongs to large-diameter slurry pump, it is necessary to remove the impeller removal ring and rotate the impeller in the opposite direction. Troubleshooting: first increase the water pressure then inject water into the pump body, and then start the pump. At the same time check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws.Jerada, So it is called: submersible slurry pump. The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump. Therefore, when the pump temperature is too high, you dont need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time and then take relative measures to effectively solve it.
The mixing impeller and other main flow passage parts are made of high wear-resistant materials,ShaalisaSubmersible sewage pump, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing It can be done. For example, before the test run, the motor and the main pump are separated from the test in the positive and negative directions, including glue, etc. The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.reform, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure. When the submersible slurry pump is used at ordinary times, cavitation usually occurs,ShaalisaWQ submersible pump parameters, which has a great impact on the impeller of the equipment itself. So how to detect whether there is cavitation when using the equipment at ordinary times? The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Lets take a look at the correct disassembly of the impeller
If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.Design brand, Next, the water seal, lock ring and other parts need to be installed. Functions of cf fire control cabinet: Strengthen management. Normally, the use and daily management of fire pumps require manual operation maintenance and management. However, once large shopping malls are encountered and there are a large number of similar fire pumps, oneortwo managers are often unable to manage them, For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?Shaalisa, The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature. Most of the time, we dont know how to choose the pump when we buy it. In fact, when we use it, the flow is small Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can