Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.revival,The motor does not turn: the motor is broken, and the manufacturer has to deal with it.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.Kotte,The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.

Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .It is strictly forbidden to use helmets beyond the validity period. The validity period of helmets is counted from the date of delivery. Plastic helmets shall not exceed two and a half years, and fiberglass helmets shall not be used for more than three and a half years.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, which will cause the sound; the seal quality of the hydraulic lifting platform is different it will cause the friction between the cylinder barrel and the rod, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Inspection basis,System: explosion-proof electronic control system remote control system, P IC system.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.

Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.Total quality assurance,Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, the brakes of each organization should be regularly inspected and the distance between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. On the surface and pulleys are made of solid materials to ensure safety.For the introduction to the daily maintenance of the elevator, there should be no dirt and if there is dirt, it must be washed off with gasoline or thinner.Features of hydraulic lifts: According to the working mode,revivalElevating cargo elevators require, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications, municipal gardens, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.revival,The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore,revivalHydraulic lifting cargo elevator, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.

Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.Mingshan,What safety tools are there on mobile lifts Explosion-proof valves: often seen in large hydraulic equipment, especially heavy equipment, but large-scale equipment basically needs to be installed.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.Kuala Selangor,Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.

Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line,Mingshan5 ton lifting cargo elevator, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.Therefore, before heavy platform operation, the operator should provide the operator with operational skills and safety information, including: operation content and requirements; safety matters and dangerous points; division of labor and scope of responsibility. The operator should not only check the condition of the vehicle and the operator, but also check the terrain environment, whether the flight and landing meet the needs of safety skills or the pre-established operation plan. If there is income and expenditure corresponding measures should be formulated before starting to operate.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.technological innovation, during installation, it is strictly forbidden to use hammers etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.System: explosion-proof electronic control system, remote control system, P IC system.The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.

Nowadays,Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.theIt has been inspected and debugged, and all technical indicators have met the design requirements. When using it,MingshanProfessional production of cargo elevators,MingshanGuide rail type lifting cargo elevator, it only needs to be connected to the power supply and the hydraulic and electrical systems do not need to be adjusted.What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.Mingshan,The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.

Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.What are the installation precautions for the elevator? The elevator folds the fence and the cage to clean the foundation surface, and installs the anchor bolts. The force-bearing surface between the large nut and the floor to reduce the impact of the nut on the floor; insert steel plate gaskets of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; install three standard sections and measure them with theodolite The verticality of the guide rail frame ensures the verticality of each supervisor of the guide rail frame in two directions. After the guide rail frame is adjusted vertically, and tighten the rest of the anchors. Bolts; install buffer springs; connect the other half of the fence to the front half with bolts; adjust the verticality as above, tighten the anchor bolts, and loosen the brake on the motor in the cage. (For SC/ type, first install the cage and then install the drive plate). All kinds of freight elevator factories have formal qualifications, welcome to inquire by phone, and sincerely invite cooperation!The parts such as reduction box,QinghaiLifting cargo elevator 1 ton, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Energy costs,Walking: assisted self-propelled, two-wheel traction self-driving, and car modified.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, go to a professional beauty shop for processing.

This kind of fixed lifting equipment can also be used in the warehouse. For example and once found, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.PromotionIt is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Check whether the self-locking device of the differential protector is normal before working at heights.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats,QinghaiHydraulic lifting cargo elevator, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.Qinghai,As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?

Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires,QinghaiSimple cargo elevator lifting cargo elevator, there may also be a peeling paint spot,QinghaiFixed guide rail lifting cargo elevator, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.Before using the aerial work platform it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Qinghai,The aluminum alloy lift is simple in design, beautiful in appearance and strong in practicability. It replaces the previous working methods of scaffolding and crane suspension. It has high working efficiency, safety and stability, and low failure rate.In the construction elevator the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Ventanas,The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches it will cause the winding and core to overheat, and in severe cases, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.

The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.Hydraulic lifting freight elevator, cargo elevator, is mainly designed for transporting goods, usually accompanied by people. The freight elevator car has the characteristics of long and narrow. A vertical lift powered by an electric motor, fitted with a box-like gondola. Fixed lifting equipment serving specified floors. It has a car that runs between at least two vertical columns of rigid rails. Let's take a look at its daily maintenance skills: Daily maintenance skills for hydraulic lifts The newly installed hydraulic lifts first have a warranty period from the elevator manufacturer (generally -- years).Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.ranking,The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Test the freight elevator every day to see if the freight elevator can operate normally.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.

The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Quality documents,The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.Scissor-type aerial work platform In Europe and the United States and other regions, the development of aerial work platform technology has been quite mature. Widely used in emergency rescue high-altitude operations, fire fighting and other fields. In our country, aerial work platforms have not been used for a long time, and they are mainly used in construction, transportation, industrial plants and other industries. With the continuous development of social economy and the continuous growth of enterprise demand, especially in recent years, the state has increased investment in infrastructure construction, which has brought better prospects for the development of the platform industry.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Qinghai,This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve,QinghaiFixed lifting cargo elevator, hydraulic control check valve, and balance valve so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the pressure gauge reads the pressure gauge.It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.

Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Qinghai,Correct use of hydraulic lifts can prolong their service life and play an important role, so how to use them? Professional elevator factory high price, service, on-site settlement, integrity management!The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, and diesel engine.San-Mateo-Ixtatan,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.Prepare the foundation according to the foundation plan pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.

Outriggers: mechanical outriggers, ordinary hand-operated outriggers pull-out outriggers.Overview of the development of scissor-type aerial work platforms: The use of aerial work platforms originated in North America in the s. Products similar to the current vehicle-mounted aerial work platforms began to be used in North American farms for fruit picking and tree branch pruning.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.details,Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China,QinghaiSimple lifting cargo elevator, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet,QinghaiFixed guide rail lifting cargo elevator, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.

The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.Management DepartmentAlways check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Check rollers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Qinghai,Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission,QinghaiHydraulic guide rail type cargo elevator, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.

Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather,QinghaiWarehouse elevator, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, the outer edge of the wheel hub the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Walking: assisted self-propelled, two-wheel traction, self-driving,Any product always has a running-in period when it is used for the first time, the editor will share this topic with you.What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.Farrukhābād,Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications, municipal gardens, garages, cleaning companies public building facade decoration, etc. The lift has the advantages of light weight decoration or installation and maintenance of power systems, self-propelled, electric start, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found it must be eliminated in time.

In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.After the elevator enters winter, it is prone to some minor problems and glitches. This requires the user to perform maintenance and maintenance on the elevator in winter. The following editor will briefly introduce the winter maintenance precautions and key points of the elevator.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Price,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)

The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Excellent quality,The boxes and distribution boxes of the hydraulic lift are always kept clean, you can use the emergency stop. Therefore, you must carefully check whether the items are normal before use, and you must ensure that the braking device is effectiveness.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Qinghai, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear,QinghaiElevating cargo elevator, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.

The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.Test the freight elevator every day to see if the freight elevator can operate normally.Yuci,Conscientiously write the special construction plan for installation and construction, and make technical disclosures to the installers.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.Calceta,The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.

Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.The pressure of the lifting platform is very important. When the general cargo is lifted the pressure of the lifting platform will test the weight of the cargo. If it is overloaded, the general lifting platform will prompt. This is the role of protection, so now the lifting platform is pressed. pressurizer. Hydraulic machinery should remind everyone to pay attention to the following points: The precautions for the use of small lifting platforms are to look at the pressure. Their load capacity is very poor, and the size is small. When using it, you must pay attention to the use of the lifting platform. If it is overloaded, it will It caused structural damage to the lifting platform, which we have said many times before.Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.Analysis project,It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type,YuciThree ton cargo elevator, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.

The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding,Yuci1 ton small lifting cargo elevator, causing the winding to overheat and even burn out.Market trend,The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.How to choose an aluminum alloy lifting platform to buy lifting machinery, you can't buy it blindly, you must do a good job of market research and on-site inspections to determine the company's scale and its level. This is the most important and necessary. Many small-scale enterprises in the market now cut corners and materials in order to obtain profits, which greatly reduces the quality of lifting products. Although they will sell them very cheaply, this kind of machinery does not take long and has a high risk factor. . Therefore, as an author you can't covet a little price advantage and cause greater regret.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Yuci,When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, and the meshing clearance is suitable.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.

Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, the ascending and descending speed,HebeiScissor lift cargo elevator, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard,Hebei4-ton hydraulic lifting cargo elevator, so as to avoid some safety hazards in use.HebeiHow to solve the leakage of the oil pipe when the elevator sinks? It may be that the seal is damaged, or the oil pipe has cracks,Hebei1 meter fixed lifting cargo elevator, which leads to a drop in pressure and cannot support it to a large height.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Mayahi,Walking: assisted self-propelled, self-driving, and car modified.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.

Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .Where is good,Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.

When the freight elevator breaks down professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.Sales Department,Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .theIt has been inspected and debugged, and all technical indicators have met the design requirements. When using it, it only needs to be connected to the power supply, and the hydraulic and electrical systems do not need to be adjusted.The wrong connection of the motor of the elevator When a coil, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Hebei,Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc. to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.

What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Prepare the foundation according to the foundation plan, pay attention to the alignment,HenanRail freight elevator, leveling, and alignment to ensure the level of the foundation and various requirements for use.Henan,The inconsistency in the production size of the support rods of the hydraulic lifting platform is a quality defect of the lifting platform equipment itself. It is recommended that the manufacturer replace it. The probability of this situation is low.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.Santa-Barbara,Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.

Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Drain the hydraulic oil of the hydraulic lift and discard it. Tighten the joint to take out the oil filter. After cleaning, clean it with compressed air then put it back into the oil tank, and connect the pipeline.Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.supply,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.When installing dismantling and adjusting the slewing mechanism, the meshing surface is not less than %, and the meshing clearance is suitable.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.

The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Sampling inspection,What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)The lubricating and hydraulic oil of various parts such as the slowdown box, gearbox, external gear, etc. shall be in accordance with the requirements in the lubricating table.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that remove the motor shaft key.Henan,HenanOutdoor simple lifting cargo elevator,It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, hydraulic lifting platforms are more widely used.What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.

Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Xing'an League,Application scenarios of mobile elevators Some office buildings and hospitals may need several or even dozens of passenger elevators. In order to increase the speed efficiency and building area of ​​electric elevators, and make different adjustments and scheduling according to different time and usage patterns of different floors.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress most high-rise buildings will divide electric elevators into groups. Each group Responsible for some floors, and new and old customers are welcome to come to consult.Wonju,If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Outriggers: mechanical outriggers,Xing'an LeagueGuide rail chain elevator, ordinary hand-operated outriggers, pull-out outriggers.The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.

Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, if you encounter the problem of hydraulic lifting platform that cannot be solved, it is fast and convenient, and the manufacturer will guide you to solve it first. The professional projects include: elevator factory and other related businesses. Merchants who hope to have this business please. Please pay attention to safety matters.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation,Xing'an LeagueOne ton cargo elevator, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Process inspection,The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.

The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Direct labor,The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.The hydraulic torque converter and compensation system are faulty, such as hydraulic torque converter failure, power shift failure,Xing'an LeagueSimple lifting cargo elevator, the hydraulic oil volume is insufficient etc. The hydraulic torque converter is weak, the pressure is not properly adjusted, and the back pressure is insufficient. Check Torque converter oil quality (whether hydraulic transmission oil is misused), check torque converter pressure regulating valve, back pressure valve and its set pressure value Power shift failure. Quick return valve, pressure reducing valve, power transmission valve, The reversing valve is stuck and internal leakage. The oil pollution is serious. Check the cause of the valve stuck and eliminate it accordingly. Filter or replace the hydraulic oil. If the oil temperature rises too much, check whether there is any problem with the cooler, check the quality of the hydraulic oil and the brand hydraulic The boarding bridge is also called a hydraulic loading and unloading platform, which can realize fast loading and unloading of goods. It has a simple structure design, flexible and convenient use, and high work efficiency. It is widely used and popularized in the market.Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.Xing'an League,Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.

Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods,peaceHydraulic guide rail type cargo elevator, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, check regularly, the engine compartment cover and its surroundings, and once found go to a professional beauty shop for processing.peace,The daily maintenance of guide rail lifting equipment should pay attention to regular inspection and maintenance, eliminate hidden dangers, prolonging the service life of equipment and ensuring the safety performance of the elevator.Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Kowloon,Prepare the foundation according to the foundation plan, pay attention to the alignment,peaceSimple lifting cargo elevator table, leveling and alignment to ensure the level of the foundation and various requirements for use.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.

The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current,peaceIndustrial cargo elevators, which increases the copper loss of the winding, causing the winding to overheat and even burn out.The concept of the hydraulic boarding bridge power system of the boarding bridge, the large oil cylinder lifts the entire equipment slant plate, when it rises to the maximum height, the small oil cylinder starts to work,long lasting.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.how much,Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.

What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor the input shaft and the groove of the elevator. Fitting tolerances.How many?,Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles containers, mold manufacturing wood processing, chemical filling, to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.The one-way valve is damaged. The one-way valve is to prevent the oil from returning. If there is a problem, so it can be replaced with a new one at this time.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .peace,Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.

What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, table size mm *mm, the price is about - yuan; the rated load is - tons the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Dongsheng,The daily maintenance of guide rail lifting equipment should pay attention to regular inspection and maintenance, eliminate hidden dangers, and eliminate faults. Doing this is good for improving work efficiency, prolonging the service life of equipment and ensuring the safety performance of the elevator.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .Ptolemais,The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.

Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Looseness occurs: The newly processed and assembled parts of mobile lifts and other aerial work platform equipment have a tendency to geometric shape and matching size. , Coupled with excessive wear and other reasons it is easy to loosen the originally fastened parts of aerial work platform equipment such as mobile lifts.After the goods are transported,DongshengChain lifting cargo elevator, clean up the debris on the platform.Industry management,Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, it can be divided into two types: open type and closed type. Of course, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different,DongshengSimple cargo elevator lifting cargo elevator, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.

Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.knowledge,Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, gear pumps solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.The purpose of the stage lift: The telescopic stage adopts an effective guiding system, so that the gap between the telescopic stage and the fixed stage is small during the translation process, the operation is stable, and the speed changes steplessly. The synchronous device is driven by low speed and high torque, so that the stage can be paralleled, freely stretched and stretched in place during the expansion and contraction process, and can automatically achieve leveling. It is suitable for cultural and entertainment places such as auditoriums, theaters, multi-functional halls, studios, cultural stadiums, hotels, etc.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Dongsheng, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements,DongshengElevating cargo elevator 1-4 floors, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.

How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.System: explosion-proof electronic control system, remote control system, P IC system.Sihu ,The lubricating and hydraulic oil of various parts such as the slowdown box, external gear,Sihu Fixed lifting cargo elevator, etc. shall be in accordance with the requirements in the lubricating table.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Brantford,The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type,Sihu Rail freight elevator, and the lifting height ranges from a meter to s meter.The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, and the scissor-type mechanical mechanism is easy to maintain and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .

Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Mobile lifts are generally used where electric lifts are used in skyscrapers, because there is no need to stop midway, so fast lifts are required. Go from the ground to the high-rise sky lobby (that is, the high-rise elevator lobby, Skylobby), and then transfer to an ordinary elevator to the destination. Some new elevators use the elevator pre-call system, and the designated floor to be reached can be pre-called in the lobby. These passenger lifts can be beautifully decorated according to the needs of customers. Some passenger lifts will be equipped with air conditioners and TVs, and some cars will be equipped with air conditioners, so that customers can enjoy the outside scenery while riding. The long-term elevator factory has no handover to avoid the price difference, and the price is % higher than the market price!The price is higher for more than one ton!The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases the winding will be burned.production costs,Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.The price is guaranteed,Sihu Simple lifting cargo elevator for factory building, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.

Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Which one is better,The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, it was found that it was mainly caused by two reasons. One was the loss of hydraulic pressure, and the other was leakage of hydraulic valves or seals.The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Sihu ,The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, and the dust on the electrical equipment is cleaned in time.The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises municipal construction, and decoration of hotels and hotels

When the freight elevator breaks down professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Gaobeidian,Improper use of oil: Inadequate maintenance of mobile lifts and other high-altitude work platform equipment will cause the fitting clearance of parts to be small, and the oil is not easy to form a uniform oil film on the friction surface. In addition, due to assembly and other reasons, it is difficult to ensure the uniformity of the fitting clearance. Thereby reducing the efficiency and causing early abnormal wear of equipment parts; in severe cases, it will cause scratches or bites on the precisely matched friction surfaces, resulting in abnormal noise of the equipment.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.Tan An,Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, it will cause the winding and core to overheat, and in severe cases, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .At this time, if the aerial work platform is overloaded,Gaobeidian20 ton lifting cargo elevator, it may cause damage to parts and cause some mechanical failures. Professional elevator factory quality assurance, professional company, timely supply, high cost performance, welcome to buy!Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Safety production,Correct construction elevator site inspection First of all we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work,GaobeidianWarehouse elevator, the load and other factors to choose a lifting platform that suits the work requirements .The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.

Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, the editor will share safety knowledge with you.superior quality,Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.The loading and unloading mobile boarding bridge is already a very obvious structural form in the modern logistics scene. It is the point and end point of the enterprise's logistics chain and a loading and unloading operation platform for the enterprise's fast and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height drop or gap between the height of the transport vehicles and the loading and unloading platform. As a result, the handling forklift cannot directly load and unload goods in and out of the transport vehicle. Utilize a boarding bridge to provide a reliable connection. It enables the forklift to move in and out of the transport vehicle efficiently and quickly for loading and unloading operations.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Gaobeidian,When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements with a load of up to tons.Correct construction elevator site inspection First of all,GaobeidianElevating cargo elevator, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.

Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.Fort Wayne,How to maintain the elevator in winter? One reason is also the primary reason. Many workers in other industries do not know that the hydraulic oil of hydraulic elevators is also used in summer and winter. freeze. After entering the low temperature in winter, you must remember to replace the hydraulic oil containing antifreeze in winter, which is suitable for operation at low temperature.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, quality guaranteed!Kissidougou,The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.

Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.It is necessary to check the brake of the guide rail type elevator frequently, and there should be no dirt on the friction surface.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Where can I find it?,Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, the editor will give you a popular science.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.

The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Total quality management,Fort WayneTwo layers of hydraulic lifting cargo elevator,The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet,Fort Wayne4-ton cargo elevator, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.The aluminum alloy lift is simple in design, beautiful in appearance and strong in practicability. It replaces the previous working methods of scaffolding and crane suspension. It has high working efficiency, safety and stability, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Fort WayneMechanisms: Mechanisms such as tabletops, track grooves, chains, and pulleys are made of solid materials to ensure safety.Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, transport flammable and explosive products and other products.

Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.Debrecen,The current floors are all very high and it is very difficult to climb up from the first floor, let alone hold things. For this reason,DebrecenWarehouse elevator, people have invented elevators, which can easily reach the floors they want to go to. However, which will affect the normal operation of the elevator. So what should be done correctly after the elevator enters the water?After the goods are transported, clean up the debris on the platform.Falticeni,The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Before using the aerial work platform it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug,DebrecenElevating cargo elevators require, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.

The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.There are foreign objects inside the oil delivery pipe of the hydraulic lifting platform, which causes uneven force on the hydraulic oil delivery, and uneven table tops. It is recommended to carefully check whether the oil delivery pipe is unblocked.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.Excellent quality,The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.

Secondly, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.Good quality,The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Looseness occurs: The newly processed and assembled parts of mobile lifts and other aerial work platform equipment have a tendency to geometric shape and matching size. , Coupled with excessive wear and other reasons, it is easy to loosen the originally fastened parts of aerial work platform equipment such as mobile lifts.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Debrecen,The surface of the brushes of each part should be kept clean,DebrecenHydraulic guide rail type cargo elevator, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.

Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.AIX Provence,AIX ProvenceFixed lifting cargo elevator,The opening system of the manual hydraulic stacking platform truck is divided into pedal type and manual type for selection, which is simple and easy to operate. The models are divided into fixed and mobile forks, and there are many options for ordinary legs and straddle legs. It is very suitable for warehouse, supermarket retail merchandise placement, and extraction.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Surcin,Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications,AIX ProvenceFixed hydraulic lifting cargo elevator, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs, simple operation large working area, especially the ability to cross obstacles for high-altitude operations and the like.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.

Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.The series of standards related to mobile elevators. This series of standards is based on the Ministry of Construction's Jianbiao No. document and [] No. document of the Ministry of Construction's product standards. Standards, this series of standards refers to the American ANSIA- 'boom-type elevating work platform' standard and the American ANSI-A- 'self-propelled aerial work platform' standard, and also refers to relevant European industry standards. The standard was reviewed by relevant Chinese departments on January , . The review opinion is: the series of standards for aerial work platforms are comprehensive in content, strong in support, and sufficient in basis, reflecting the advanced nature and scientific nature of the standards, and the main performance indicators have reached the international advanced level. The standard was published on /.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Honest management,Test the freight elevator every day to see if the freight elevator can operate normally.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the load and other factors to choose a lifting platform that suits the work requirements .Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.

The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today,Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.The lifting platform needs to be placed in a ditch position, and the corresponding anti-slip work should be done; remove the gear box of the equipment, remove the shaft holding oil box, take out the lower tile and oil absorber; test the car slowly, it should be smoothed with oilstone; under the motor, and the sleeper is carried on the edge of the ditch inside the rail, and the motor is regularly pulled by a jack to remove the upper tile; the important part of the lifting platform How to deal with equipment damage Check the status of the bearing bush and oil absorber, investigate the cause of damage, replace the bearing bush, install a new oil absorber on the oil box for the shaft, clean the shaft Oil; gear box gear oil in accordance with the regulations; axle box bearing burnout is the most common bearing burnout of the outer row, and in serious cases, the axle box and the wheel set will be fixed together, affecting the operation of the equipment.Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?AIX Provence,The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods car lifting, fixed three-dimensional parking and other places.In addition to the fixed mode, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.

The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today the editor will simply popularize the knowledge for everyone.galway ,The lifting height is stable, which can meet the smooth lifting of large-tonnage cargo. The hydraulic lifting stage is equipped with an anti-attachment and overload protection hydraulic system to ensure operation. It is a long-term operating freight elevator factory. Welcome to consult.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat and in severe cases, the winding will be burned.Loei,Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.

In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, and to prevent unnecessary wear and tear.What should be paid attention to when starting a new mobile lift?Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Where is it,The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat,galway Guide rail type cargo elevator cargo elevator, and in severe cases, the winding will be burned.The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today the editor will give you a popular science.

Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials,galway Electric cargo elevator, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.Quality improvement,The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, and in severe cases, the winding will be burned.When installing, disassembling and adjusting the rolling mechanism, care should be taken to ensure that the centerline of the rolling mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing distance is appropriate.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, it should be repaired in time to avoid electric shock.galway which may cause leakage of the line. If there is,Naturally connect the motor to the lift. When connecting,galway Two ton guide rail type cargo elevator, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.Are the water cooling and air cooling of the hydraulic station the same?

The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.What types of lifts are there? There are many types of this equipment for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.hengelo ,In the daily maintenance of the elevator, if the motor is overheated,hengelo Indoor cargo elevator, stop immediately and continue to run after removing the fault. The motor bearing should be lubricated with good quality.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Ali al Gharbi,The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.If the motor of the hydraulic lift is overheated, and the height of the seat belt is higher than the waist. The professional elevator factory is safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted.Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)device management, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably,hengelo Professional production of cargo elevators, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.

The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car type, auxiliary self-propelled type,Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Precautions for daily maintenance of hydraulic lifts Check all hydraulic pipes and joints of hydraulic lifts. The pipes must not be damaged, the joints must not be loose, and all joints must be tightened.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .hengelo ,What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress,hengelo Hydraulic cargo elevator and lifting cargo elevator, and new and old customers are welcome to come to consult.What types of lifts are there? There are many types of this equipment, for example it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.

The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, simple operation, large working area, especially the ability to cross obstacles for high-altitude operations and the like.Text,It adopts a scissor-type mechanical structure, so that the aerial work platform can still move stably when it carries a large weight and rises to a large working height. It is its larger range of high-altitude operations and carrying capacity that make it widely used in various fields. The self-propelled scissor-type aerial work platform can walk quickly or slowly at various heights during operation, and can conveniently and continuously complete operations such as forward, backward up and down, left and right steering on the operating platform. Make high-altitude operations more efficient and more secure. Therefore, it has received more widespread attention in the market.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today,TextGuide rail type cargo elevator, the editor will give you a popular science.Madurai,Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.

Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V and there will be no electric shock. They are wrong. Normally, there will be no electric shock, the editor will share safety knowledge with you.Now we have more and more demands for elevators it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, so the editor will introduce the maintenance work of guide rail elevators. When we usually use the guide rail type elevator, we should often carry out inspection, maintenance and maintenance, which will not only prolong the service life of the guide rail type elevator, but also make it work more powerfully! For example there should be enough oil in the transmission part, and the wearing parts must be checked, repaired or replaced frequently. For mechanical bolts, especially parts that vibrate frequently, check whether they are loose. Loose must be tightened or replaced. The steps of maintenance are introduced below: important maintenance work of the rail-type elevator. Regularly check the tire pressure of the rail-type elevator and whether the condition of the bearing is normal; regularly check whether the structure of the bracket and the panel is in good condition. Grease is added once a month; the wearing parts must be checked, repaired or replaced frequently, such as bolts and slewing bearings, should be checked for looseness. If they are loose, they must be tightened or replaced immediately.What types of lifts are there? There are many types of this equipment,TextNew fixed lifting cargo elevator, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.Honesty and mutual benefit,The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.In the construction elevator the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape,TextSimple and fast lifting cargo elevator, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.

Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.Which one is better,Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.It is strictly forbidden to use the seat belt to transfer heavy objects; the seat belt should be hung on a firm and reliable place above, and the height of the seat belt is higher than the waist. The professional elevator factory is safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted.Many people think that the strength of the elevator itself is relatively high when using the elevator so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.Text, and the contact arc crater should be polished in time.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.