Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point. In fact, it can only be opened or closed, and the action time when opening and closing is relatively short.Damgan, the impeller of the slurry pump becomes tighter and tighter as it turns. The more it is used, the easier it will operate. However, if the slurry pump reverses,DamganPipeline pump body, it will directly cause the impeller of the slurry pump to fall off. The slurry pump must be disassembled and then re inspected, installed and tested. It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump,DamganSplit vertical pipeline pump, Submersible pump is a common water lifting equipment for deep wells. During operation we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.Cowin, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains etc. Submersible pump is generally divided into clean water submersible Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However if the thrust rubber water seal is used, when Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but because
the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer. In recent years, domestic stainless steel pipeline pump products have greatly improved their technical level through introduction absorption, renovation, digestion and innovation, especially the supporting products of some major technical equipment have reached or approached the advanced level of similar products. We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used, so it is effective when it is used in many mountainous areasmarket, The type selection design of submersible slurry pump has a great impact on the service life and operation stability of slurry pump. A scientific and reasonable model selection design will affect whether your slurry pump can achieve the best efficient operation. Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities. The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump
After the submersible slurry pump leaves the factory,DamganDeep well pump, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.Where can I find it?, After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, nor a short-term product, but a long-term equipment. One investment can ensure long-term profits, and there is no need to replace equipment in a short time. Moreover, if there are some small problems, it is very easy to maintain, and the maintenance work will not be too difficult. therefore Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.Damgan, The pump should be divided into two aspects: electricity and machinery. As for machinery, you can compare the previous maintenance records. The second is electricity. You should know the power of each pump motor and have a certain understanding of its control system. Slurry pump with mechanical seal Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation. For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?