The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller),SapporoSubmersible sewage pump, magnetic dial indicator, outside micrometer, caliper, feeler gauge, square ruler, copper bar, screwdriver with handle,SapporoScrew deep well pump, hammer, clean kerosene, oil basin, cotton yarn, Determine whether repair and replacement is required according to the wear condition of the ring; Check the insulation of the motor stator to see if there is any trace of chamber sweeping damage; Check whether there is sand deposition and sewage blockage at the pump bottom, whether there is sand deposition at the pool bottom, and whether it is necessary to cut off water and clear silt. Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.Santiago del Torno, Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly, and tighten the screws. The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss. So it is called: submersible slurry pump.
The water pump is not only the water supply for the city, but also the household water purifier used in our home. There is a with pump equipment to help us purify water. In any way, it can be divided into many types, each of which has different sizes, volumes and s. Therefore, many people believe that Determination of lift It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.Service first, Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.
If there is a standby pump and tighten the two dust discs and fasten them on the shaft. adjustment drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!Packaging strategy, selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, particle size, shape, hardness,SapporoVertical multistage centrifugal pipeline pump, concentration, acid alkali and other characteristics of the transported materials. when the deep well pump is put into water for use, pay attention to protect the cable. The cable must not be stressed to prevent damage. The lifting weight of the lifting device (such as tripod, hoist or electric hoist) used shall be greater than the weight of the submersible pump, and enough space shall be reserved. A wood that is tied to the wellhead with a rope First of all, lets understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulationSapporo, The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed. In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines. Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload